Duct not aligned

"Bad panel or main PCB. Need AUTHO. Main PCB NLA; rqstng P&A on 1 DC97-22903A (ASSY CONTROL PANEL **(AUTHO NEEDED)**), ordrng 1 DC94-11888A (ASSY PCB EEPROM **(AUTHO NEEDED)** NLA), states that autho needed"

"Tested on Timed Dry and Automatic Dry, both checked ok and did not cut off prematurely. Tested exhaust vent to the outside and measured 0.80+ H2Oin standard is 0.50. Dryer vent needs to be cleaned which could be causing the dryer to over heat due to not having proper air flow. Unable to duplicate any issue"

Cleaned out drain pump and wash pump

Installed new belt and all checked okay; used 3 W10721967 (DRIVE PULLEY) from stock

Adjusted valve and everything checked out okay

Instructed to switch to liquid or powder

Burner cap misaligned

Bad transformer.

Error code 7-1 bad control heating circuit.

Cleaned out filter and did a deep clean on rubber gasket. Cleared out rubber gasket drain tube.

"Installed new timer and solenoid. Dishwasher resumed normal function . During more thorough tests I found that the motor is humming during the drain cycle and not operating correctly intermittently. Motor assembly will need to be replaced. Unit is old and additional repairs for it's age are not uncommon.Left message to owner notifying of the current status of the repair. Additional repairs will cost at least $200+; saved tckt , states that autho needed"

Tightened screw underneath pulley and all okay; (serial indicated as 'NotAvailable' so system created UIS w/pseudo #)

Minimal basket warp.

"Installed parts, all checked okay.; used 5 3387747 (ELEMENT) from stock"

"Installed parts, all checked okay."

"Installed parts, all checked okay."

Not switching to spin and no sound from panel speaker.; ordrng 1 W11419171 (CONTROL) and 1 W10754448 (CLUTCH) and 1 W11478526 (PANEL-UI)

"Installed parts, all checked okay."

"Installed parts, all checked okay."

Bad control and thermostat

"Needs new damper, making a lot of noise and going bad."

"Dryer has a bad motor and possibly a bad timer. Customer stated that the last company replaced the motor. Motor did not appear new. Replacing ; (serial indicated as 'NotAvailable' so system created UIS w/pseudo #), states that autho needed"

"Bad capacitor, replaced and all checked ok. Had reset control as well; used 1 W11395618 (CAPACITOR) from stock"

"Cx states that the left front burner, on simmer, does not stay lit. Checked gas flow and increased it with knob adjuster. No difference. Found that simmer orfice was clogged with debris and cleaned with cleaning tool. Cx states that there is also an issue with the bake convection temperature reaching preheat and then dropping out. Tested at 350° and it did preheat but did not reignite to go back up to temp. Ordering required parts to complete the repair. ; ordrng 1 W10860916 (MODULE SPARK) and 1 WPW10324262 (IGNTR-OVEN) and 1 W11685628 (CONTROL (autho item))"

"Installed parts, all checked okay."

"Installed parts, all checked okay."

Found bad blower fuse. Recommended dryer vent cleaning. Cleaned out dryer for free just because customer was so nice.; used 1 3392519 (THERMAL FUSE) from stock

"Installed parts, all checked okay."

"Installed parts, all checked okay."

"Installed parts, all checked okay."

"Bad blower wheel; ordrng 1 WP697772 (WHEEL, BLOWER (M024))"

Bill out for parts. Replacing on new ticket

Bad timer. Won't stop; ordrng 1 WPW10185982 (TIMER)

"Installed parts, all checked okay.; used 1 3387747 (ELEMENT) from stock"